Professional heating, cooling & air quality services serving Dallas and surrounding communities in Texas. NATE-certified, 24/7 emergency response.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
Over time, air ducts accumulate dust, pet dander, mold spores, and construction debris that degrade indoor air quality and restrict airflow. Professional duct cleaning uses negative-pressure HEPA-filtered vacuums and rotary brush systems to remove contaminants from supply and return plenums.
When your boiler produces inconsistent heat, unusual noises, or pressure fluctuations, the root cause often involves sediment buildup, failing motorized valves, or degraded seals within the hydronic loop. Experienced technicians restore system balance and verify safe operation through combustion analysis.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
A correctly sized heat pump installation eliminates the guesswork of mismatched equipment and undersized ductwork. Our technicians perform load calculations, verify airflow across the evaporator coil, and commission the system to manufacturer specifications for peak efficiency and longevity.
Professional smart thermostat installation goes beyond mounting and Wi-Fi pairing. Technicians verify your system has the necessary common wire, confirm compatibility with multi-stage heating and cooling equipment, and program setpoints and schedules tailored to your household for immediate energy savings.
Sudden HVAC failures often stem from compressor lockout, blown transformer fuses, failed gas valves, or tripped high-pressure switches. Emergency repair service provides same-day response with technicians equipped to diagnose and resolve critical faults across all major heating and cooling equipment brands.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
The Dallas metropolitan area spans diverse neighborhoods, building types, and HVAC system configurations — and KIC Refrigeration has heating and cooling expertise across all of them. With a population of 1,337,417, Dallas is one of the largest markets we serve, and we have invested in local teams who understand every corner of the metro from historic downtown buildings to sprawling suburban developments.
From older Dallas districts with original gravity furnaces and radiator systems to newer subdivisions with dual-fuel heat pump setups, our crews adapt their approach to match the specific needs of each property. We stay current on Texas energy code updates, work with every utility rebate program in the Dallas area, and maintain supply chain relationships that keep your project on schedule and on budget.
Built on NATE certification, transparent pricing, and a guarantee that we stand behind.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Answers to the heating and cooling questions our customers ask most often.
A comprehensive HVAC inspection from KIC Refrigeration in Dallas covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Yes. The EPA estimates that Energy Star certified smart thermostats save Dallas homeowners an average of 8 percent on heating and cooling costs annually, which translates to $50 to $150 per year for a typical household. Models from Ecobee, Nest, and Honeywell Home use occupancy sensors, geofencing, and learning algorithms to build a schedule around your actual habits, automatically lowering temperatures when you leave and restoring comfort before you return. Many smart thermostats also provide energy usage reports, filter change reminders, and maintenance alerts that help you keep your system running efficiently. Some Texas utility providers offer rebates of $50 to $100 on qualifying smart thermostat purchases, further reducing the cost. KIC Refrigeration installs and configures smart thermostats to communicate properly with your specific HVAC system — including multi-stage equipment and heat pumps that require specialized wiring.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Dallas and surrounding Texas communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Dallas require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Texas mechanical codes and International Mechanical Code standards.
HVAC repair costs in Dallas typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
Most residential HVAC installations in Dallas, TX are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"KIC Refrigeration handled our emergency furnace repair during a cold snap. They prioritized us because we have elderly parents in the home. Truly caring people."
"KIC Refrigeration repaired our heat pump when two other companies said it needed full replacement. Saved us thousands. Still running great six months later."
"AC tune-up went well. Found a refrigerant issue I did not know about and topped it off. Fair pricing and honest work."
Our NATE-certified crews provide HVAC service throughout the surrounding area.